What are your thoughts regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a tub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is conveniently available, the project can move immediately; if you need to open up a wall to eliminate the old bathtub and also position the new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually qualified yourself for the job as well as fit trying it. As opposed to hiring a contractor to take over a halfway-completed project, it is much better to think about utilizing one prior to you begin. Possibilities are you might require a specialist plumber to make tube links.
This post will certainly aid you mount a brand-new bathtub in your washroom if you have actually currently gotten a brand-new bathtub as well as do not need to alter the plan of your previous supply of water pipes.
Your tools as well as material checklist ought to make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be quite problematic due to the limited gain access to that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washers remain in area between the faucet and the sink. Protect the faucet in place with the maker offered backnut. As soon as the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The previous type must be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Making use of the two wooden boards under its feet, position the bathtub in the required setting. The wooden boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the bath tub till the level checks out degree.
To mount faucets, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the water system and also examine all joints and also brand-new pipework for leaks and tighten them if required. Fill up the tub as well as likewise examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the tub ought to wait until the bathtub has actually been made use of at the very least once as this will certainly resolve it right into its last setting.
Getting ready for the Installation
To start with, the sustaining framework supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets unit to stop pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its final setting.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post about Installing A Bathtub. Thanks for finding the time to read our posting. Do you know about another individual who is intrigued by the niche? Take a moment to promote it. Thanks for taking the time to read it.
Explore